[PDF] Synthesis And Self Assembly Of Multiple Thermoresponsive Amphiphilic Block Copolymers eBook

Author : Jan Weiss
Publisher :
Page : 157 pages
File Size : 46,70 MB
Release : 2011
Category :
ISBN :

GET BOOK

In the present thesis, the self-assembly of multi thermoresponsive block copolymers in dilute aqueous solution was investigated by a combination of turbidimetry, dynamic light scattering, TEM measurements, NMR as well as fluorescence spectroscopy. The successive conversion of such block copolymers from a hydrophilic into a hydrophobic state includes intermediate amphiphilic states with a variable hydrophilic-to-lipophilic balance. As a result, the self-organization is not following an all-or-none principle but a multistep aggregation in dilute solution was observed. The synthesis of double thermoresponsive diblock copolymers as well as triple thermoresponsive triblock copolymers was realized using twofold-TMS labeled RAFT agents which provide direct information about the average molar mass as well as residual end group functionality from a routine proton NMR spectrum. First a set of double thermosensitive diblock copolymers poly(N-n-propylacrylamide)-b-poly(N-ethylacrylamide) was synthesized which differed only in the relative size of the two blocks. Depending on the relative block lengths, different aggregation pathways were found. Furthermore, the complementary TMS-labeled end groups served as NMR-probes for the self-assembly of these diblock copolymers in dilute solution. Reversible, temperature sensitive peak splitting of the TMS-signals in NMR spectroscopy was indicative for the formation of mixed star-/flower-like micelles in some cases. Moreover, triple thermoresponsive triblock copolymers from poly(N-n-propylacrylamide) (A), poly(methoxydiethylene glycol acrylate) (B) and poly(N-ethylacrylamide) (C) were obtained from sequential RAFT polymerization in all possible block sequences (ABC, BAC, ACB). Their self-organization behavior in dilute aqueous solution was found to be rather complex and dependent on the positioning of the different blocks within the terpolymers. Especially the localization of the low-LCST block (A) had a large influence on the aggregation behavior. Above the first cloud point, aggregates were only observed when the A block was located at one terminus. Once placed in the middle, unimolecular micelles were observed which showed aggregation only above the second phase transition temperature of the B block. Carrier abilities of such triple thermosensitive triblock copolymers tested in fluorescence spectroscopy, using the solvatochromic dye Nile Red, suggested that the hydrophobic probe is less efficiently incorporated by the polymer with the BAC sequence as compared to ABC or ACB polymers above the first phase transition temperature. In addition, due to the problem of increasing loss of end group functionality during the subsequent polymerization steps, a novel concept for the one-step synthesis of multi thermoresponsive block copolymers was developed. This allowed to synthesize double thermoresponsive di- and triblock copolymers in a single polymerization step. The copolymerization of different N-substituted maleimides with a thermosensitive styrene derivative (4-vinylbenzyl methoxytetrakis(oxyethylene) ether) led to alternating copolymers with variable LCST. Consequently, an excess of this styrene-based monomer allowed the synthesis of double thermoresponsive tapered block copolymers in a single polymerization step.

Author : P. Alexandridis
Publisher : Elsevier
Page : 449 pages
File Size : 20,28 MB
Release : 2000-10-18
Category : Science
ISBN : 0080527108

GET BOOK

It is the belief of the editors of this book that the recognition of block copolymers as being amphiphilic molecules and sharing common features with other well-studied amphiphiles will prove beneficial to both the surfactant and the polymer communities. An aim of this book is to bridge the two communities and cross-fertilise the different fields. To this end, leading researchers in the field of amphiphilic block copolymer self-assembly, some having a background in surfactant chemistry, and others with polymer physics roots, have agreed to join forces and contribute to this book.The book consists of four entities. The first part discusses theoretical considerations behind the block copolymer self-assembly in solution and in the melt. The second part provides case studies of self-assembly in different classes of block copolymers (e.g., polyethers, polyelectrolytes) and in different environments (e.g., in water, in non-aqueous solvents, or in the absence of solvents). The third part presents experimental tools, ranging from static (e.g., small angle neutron scattering) to dynamic (e.g., rheology), which can prove valuable in the characterization of block copolymer self-assemblies. The fourth part offers a sampling of current applications of block copolymers in, e.g., formulations, pharmaceutics, and separations, applications which are based on the unique self-assembly properties of block copolymers.

Author : Clara Valverde Serrano
Publisher :
Page : 0 pages
File Size : 19,75 MB
Release : 2011
Category :
ISBN :

GET BOOK

Block copolymers are receiving increasing attention in the literature. Reports on amphiphilic block copolymers have now established the basis of their self-assembly behavior: aggregate sizes, morphologies and stability can be explained from the absolute and relative block lengths, the nature of the blocks, the architecture and also solvent selectiveness. In water, self-assembly of amphiphilic block copolymers is assumed to be driven by the hydrophobic. The motivation of this thesis is to study the influence on the self-assembly in water of A b B type block copolymers (with A hydrophilic) of the variation of the hydrophilicity of B from non-soluble (hydrophobic) to totally soluble (hydrophilic). Glucose-modified polybutadiene-block-poly(N-isopropylacrylamide) copolymers were prepared and their self-assembly behavior in water studied. The copolymers formed vesicles with an asymmetric membrane with a glycosylated exterior and poly(N-isopropylacrylamide) on the inside. Above the low critical solution temperature (LCST) of poly(N-isopropylacrylamide), the structure collapsed into micelles with a hydrophobic PNIPAM core and glycosylated exterior. This collapse was found to be reversible. As a result, the structures showed a temperature-dependent interaction with L-lectin proteins and were shown to be able to encapsulate organic molecules. Several families of double hydrophilic block copolymers (DHBC) were prepared. The blocks of these copolymers were biopolymers or polymer chimeras used in aqueous two-phase partition systems. Copolymers based on dextran and poly(ethylene glycol) blocks were able to form aggregates in water. Dex6500-b-PEG5500 copolymer spontaneously formed vesicles with PEG as the "less hydrophilic" barrier and dextran as the solubilizing block. The aggregates were found to be insensitive to the polymer's architecture and concentration (in the dilute range) and only mildly sensitive to temperature. Variation of the block length, yielded different morphologies. A longer PEG chain seemed to promote more curved aggregates following the inverse trend usually observed in amphiphilic block copolymers. A shorter dextran promoted vesicular structures as usually observed for the amphiphilic counterparts. The linking function was shown to have an influence of the morphology but not on the self-assembly capability in itself. The vesicles formed by dex6500-b-PEG5500 showed slow kinetics of clustering in the presence of Con A lectin. In addition both dex6500-b-PEG5500 and its crosslinked derivative were able to encapsulate fluorescent dyes. Two additional dextran-based copolymers were synthesized, dextran-b-poly(vinyl alcohol) and dextran-b-poly(vinyl pyrrolidone). The study of their self-assembly allowed to conclude that aqueous two-phase systems (ATPS) is a valid source of inspiration to conceive DHBCs capable of self-assembling. In the second part the principle was extended to polypeptide systems with the synthesis of a poly(N-hydroxyethylglutamine)-block-poly(ethylene glycol) copolymer. The copolymer that had been previously reported to have emulsifying properties was able to form vesicles by direct dissolution of the solid in water. Last, a series of thermoresponsive copolymers were prepared, dextran-b-PNIPAMm. These polymers formed aggregates below the LCST. Their structure could not be unambiguously elucidated but seemed to correspond to vesicles. Above the LCST, the collapse of the PNIPAM chains induced the formation of stable objects of several hundreds of nanometers in radius that evolved with increasing temperature. The cooling of these solution below LCST restored the initial aggregates. This self-assembly of DHBC outside any stimuli of pH, ionic strength, or temperature has only rarely been described in the literature. This work constituted the first formal attempt to frame the phenomenon. Two reasons were accounted for the self-assembly of such systems: incompatibility of the polymer pairs forming the two blocks (enthalpic) and a considerable solubility difference (enthalpic and entropic). The entropic contribution to the positive Gibbs free energy of mixing is believed to arise from the same loss of conformational entropy that is responsible for "the hydrophobic effect" but driven by a competition for water of the two blocks. In that sense this phenomenon should be described as the "hydrophilic effect".

Author : Xiaojun Wang
Publisher :
Page : 250 pages
File Size : 12,72 MB
Release : 2012
Category :
ISBN :

GET BOOK

This dissertation presents a review on state-of-the-art research of well-defined charged block copolymers, including synthesis, characterization, bulk morphology and self-assembly in aqueous solution of amphiphilic block polyelectrolytes. In Chapter 1, as a general introduction, experimental observations and theoretical calculations devoted towards understanding morphological behavior in charged block copolymer systems are reviewed along with some of the new emerging research directions. Further investigation of charged systems is urged in order to fully understand their morphological behavior and to directly target structures for the tremendous potential in technological applications. Following this background, in Chapters 2, 3, 4 and 5 are presented the design and synthesis of a series of well-defined block copolymers composed of charged and neutral block copolymers with full characterization: sulfonated polystyrene-b-fluorinated polyisoprene (sPS-b-fPI) and polystyrene-b-sulfonated poly(1,3-cyclohexadiene) (PS-b-sPCHD). Their bulk morphological behaviors in melts and self-assembly of sPS-b-fPI, PS-b-sPCHD in water were investigated. Some unique behaviors of sPS-b-fPI were discovered. The mechanisms for formation of novel nanostructures in aqueous solution are discussed in details in Chapter 4. Spherical and vesicular structures were formed from strong electrolyte block copolymers, e.g. PS-bsPCHD. Detailed light scattering and transmission electron microscopy were applied to characterize these structures. The abnormal formation of vesicles as well as microstructure effects on self-assembly is discussed in Chapter 5. In Chapter 6, we describe the successful synthesis of a well-defined acid-based block copolymers containing polyisoprene while maintaining the integrity of the functionality (double bonds) of polyisoprene. A general purification method is also presented in order to remove homo polyisoprene, polystyrene, and PS-b-PI in the di-, and tri-block copolymers. The self-assembly of PS-b-PI-b-PAA triblock terpolymers was studied in order to form multicompartmental structures in aqueous environments. In the last Chapter 7, detailed synthesis and characterization of a novel conjugate: poly(L-leucine) grafted hyaluronan (HA) (HA-g-PLeu) are presented. This work describes a new method to synthesize HA-g-PLeu via a "grafting onto" strategy. Due to the amphiphilic nature of this graft copolymers, a "local network" formed by self-assembly which was characterized by atomic force microscopy and light scattering. The secondary structure of the polypeptide was revealed by circular dichroism.

Author : Keita Fuchise
Publisher : Springer
Page : 94 pages
File Size : 24,2 MB
Release : 2014-05-22
Category : Technology & Engineering
ISBN : 4431550461

GET BOOK

In this thesis, the author describes versatile and easy-to-use methods to control the properties of thermoresponsive polyacrylamides by developing novel synthetic methods for end-functionalized poly(N-isopropylacrylamide) (PNIPAM) and block copolymers of poly(N,N-diethylacrylamide) (PDEAA). The synthesis of various urea end-functionalized PNIPAMs was achieved by the atom transfer radical polymerization (ATRP) and the click reaction. The phase transition temperature of PNIPAM in water was controlled depending on the strength of the hydrogen bonding of the urea groups introduced at the chain end of the polymer. Novel living polymerization methods for N,N-dimethylacrylamide and N,N-diethylacrylamide were developed by group transfer polymerization (GTP) using a strong Brønsted acid as a precatalyst and an amino silyl enolate as an initiator. This process enabled the precise synthesis of PDEAA and its block copolymers—namely, thermoresponsive amphiphilic block copolymers and double-hydrophilic block copolymers.

Author : José A. Pomposo
Publisher : John Wiley & Sons
Page : 504 pages
File Size : 21,80 MB
Release : 2017-08-18
Category : Technology & Engineering
ISBN : 3527806393

GET BOOK

This first book on this important and emerging topic presents an overview of the very latest results obtained in single-chain polymer nanoparticles obtained by folding synthetic single polymer chains, painting a complete picture from synthesis via characterization to everyday applications. The initial chapters describe the synthetics methods as well as the molecular simulation of these nanoparticles, while subsequent chapters discuss the analytical techniques that are applied to characterize them, including size and structural characterization as well as scattering techniques. The final chapters are then devoted to the practical applications in nanomedicine, sensing, catalysis and several other uses, concluding with a look at the future for such nanoparticles. Essential reading for polymer and materials scientists, materials engineers, biochemists as well as environmental chemists.

Author : Vitaliy V. Khutoryanskiy
Publisher : John Wiley & Sons
Page : 410 pages
File Size : 49,71 MB
Release : 2018-05-31
Category : Technology & Engineering
ISBN : 111915779X

GET BOOK

An authoritative resource that offers an understanding of the chemistry, properties and applications of temperature-responsive polymers With contributions from a distinguished panel of experts, Temperature-Responsive Polymers puts the focus on hydrophilic polymers capable of changing their physicochemical properties in response to changes in environmental temperature. The contributors review the chemistry of these systems, and discuss a variety of synthetic approaches for preparation of temperature-responsive polymers, physicochemical methods of their characterisation and potential applications in biomedical areas. The text reviews a wide-variety of topics including: The characterisation of temperature-responsive polymers; Infrared and Raman spectroscopy; Applications of temperature-responsive polymers grafted onto solid core nanoparticles; and much more. The contributors also explore how temperature-responsive polymers can be used in the biomedical field for applications such as tissue engineering. This important resource: Offers an important synthesis of the current research on temperature-responsive polymers Covers the chemistry, the synthetic approaches for presentation and the physiochemical method of temperature-responsive polymers Includes a review of the fundamental characteristics of temperature-responsive polymers Explores many of the potential applications in biomedical science, including drug delivery and gene therapy Written for polymer scientists in both academia and industry as well as postgraduate students working in the area of stimuli-responsive materials, this vital text offers an exploration of the chemistry, properties and current applications of temperature-responsive polymers.

Author : Michelle Hechenbichler
Publisher :
Page : 0 pages
File Size : 16,20 MB
Release : 2022*
Category :
ISBN :

GET BOOK

The self-assembly of amphiphilic polymers in aqueous systems is important for a plethora of applications, in particular in the field of cosmetics and detergents. When introducing thermoresponsive blocks, the aggregation behavior of these polymers can be controlled by changing the temperature. While confined to simple diblock copolymer systems for long, the complexity - and thus the versatility - of such smart systems can be strongly enlarged, once designed monomers, specific block sizes, different architectures, or additional functional groups such as hydrophobic stickers are implemented. In this work, the structure-property relationship of such thermoresponsive amphiphilic block copolymers was investigated by varying their structure systematically. The block copolymers were generally composed of a permanently hydrophobic sticker group, a permanently hydrophilic block, and a thermoresponsive block exhibiting a Lower Critical Solution Temperature (LCST) behavior. While the hydrophilic block consisted of N,N dimethylacrylamide (DMAm), ...

Author :
Publisher :
Page : pages
File Size : 23,44 MB
Release : 2008
Category :
ISBN :

GET BOOK

Self-assembly is a powerful tool in forming structures with nanoscale dimensions. Self-assembly of macromolecules provides an efficient and rapid pathway for the formation of structures from the nanometer to micrometer range that are difficult, if not impossible to obtain by conventional lithographic techniques [1]. Depending on the morphologies obtained (size, shape, periodicity, etc.) these self-assembled systems have already been applied or shown to be useful for a number of applications in nanotechnology [2], biomineralization [3, 4], drug delivery [5, 6] and gene therapy [7]. In this respect, amphiphilic block copolymers that self-organize in solution have been found to be very versatile [1]. In recent years, polymer-micellar systems have been designed that are adaptable to their environment and able to respond in a controlled manner to external stimuli. In short, synthesis of 'nanoscale objects' that exhibit 'stimulus-responsive' properties is a topic gathering momentum, because their behavior is reminiscent of that exhibited by proteins [8]. By integrating environmentally sensitive homopolymers into amphiphilic block copolymers, smart block copolymers with self assembled supramolecular structures that exhibit stimuli or environmentally responsive properties can be obtained [1]. Several synthetic polymers are known to have environmentally responsive properties. Changes in the physical, chemical or biochemical environment of these polymers results in modulation of the solubility or chain conformation of the polymer [9]. There are many common schemes of engineering stimuli responsive properties into materials [8, 9]. Polymers exhibiting lower critical solution temperature (LCST) are soluble in solvent below a specific temperature and phase separate from solvent above that temperature while polymers exhibiting upper critical solution temperatures (UCST) phase separate below a certain temperature. The solubility of polymers with ionizable moieties depends on the pH of the solution. Polymers with polyzwitterions, anions and cations have been shown to exhibit pH responsive self assembly. Other stimuli responsive polymers include glucose sensitive polymers, calcium ion-sensitive polymers and so on. Progress in living radical polymerization (LRP) methods [10] has made it possible for the facile synthesis of these block copolymer systems with controlled molecular weights and well defined architectures. The overall theme of this work is to develop novel smart block copolymers for biomineralization and biomedical applications. Synthesis and characterization of self-assembling thermoreversible ionic block copolymers as templates in biomimetic nanocomposite synthesis using a bottom-up approach is a novel contribution in this respect. Further, we have extended these families of copolymers to include block copolymer-peptide conjugates to enhance biological specificity. Future directions on this work will focus on enhancing the polymer templating properties for biomineralization by expanding the family of block copolymers with organic polypeptides and biological polypeptide scaffolds as well as a detailed understanding of the polymer-inorganic nanocomposites at the molecular level using small angle scattering analysis. Glucose responsive polymer hydrogels for drug delivery, polymer-ligand conjugates for non-viral therapy and thermoresponsive injectable photocrosslinkable hydrogels for posttraumatic arthritis cartilage healing are other applications of these novel copolymers synthesized in our work.